Fujitsu Esprimo D7010 8 vs. HP ProDesk 490 G3 Microtower

Comparison and Differences

Fujitsu_Esprimo_D7010_8.jpg case front and back pannelHP_ProDesk_490_G3_Microtower.jpg case front and back pannel
Model
Form factorSmallMini Tower
CPU optionsIntel Gen10 i3/i5/i7/i9Intel Gen6 i3/i5/i7; Celeron; Pentium;
ChipsetB460H110
Dedicated GPU *Radeon RX 6400 Low ProfileGeForce GTX 1660 Super
RAMUDIMM DDR4-2933DIMM DDR4-2133
RAM slots44
RAM speed2933 MT/s2133 MT/s
RAM max128 GB64 GB
USB ports(4x) USB-A 3.0; (4x) USB-A 2.0(6x)USB-A 3.0; (2x)USB-A 2.0;
Video ports(2x) DisplayPort 1.2DisplayPort; VGA;
Other portsRJ45; Headset, Line in; Line outRJ45; Hdph; Mic; Line-Out; Line-In; Serial; (2x) PS2;
Optional portsPS/2; VGASD card reader; Serial; Parallel;
SATA ports33
PCI slotsPCIe 3.0 x16 (wired x4)PCIe 3.0 x16; (2x) PCIe x1; PCIe 3.0 x16 (wired x4);
M.2 slotsM.2 2280/2230 M-key (PCIe 3.0 x4, NVMe)N.A.
Drive bays3.5in; 2.5in; 5.25 inch slim(2x) 3.5in; 5.25in (slim)
PSU280/300 W180/300 W
Weight8.00 kg (17.64 lb)7.05 kg (15.5 lb)
Released20202015
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Fujitsu Esprimo D7010 8 and HP ProDesk 490 G3 Microtower

If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo D7010 8 which was released in 2020. The HP ProDesk 490 G3 Microtower is older and entered production in 2015.

If you are looking for the smaller form factor the Fujitsu Esprimo D7010 8 is the right one for you. It is smaller than the HP ProDesk 490 G3 Microtower and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo D7010 8 as it is running a newer generation CPU. This is not to say that HP ProDesk 490 G3 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.

The Fujitsu Esprimo D7010 8 is using the faster 2933 MT/s RAM. The HP ProDesk 490 G3 Microtower is slower by supporting RAM speeds of up to 2133 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Fujitsu Esprimo D7010 8 as it has the ability to run 128 GB of RAM. The HP ProDesk 490 G3 Microtower can do a bit less at max 64 GB. Most of the times, this should be sufficient for the majority of users.

Ports

Both models have the same amount of USB ports for total count of 8. If this is not enough, using a USB hub is always a viable option. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.

DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the Fujitsu Esprimo D7010 8 comes with 2 ports, while the HP ProDesk 490 G3 Microtower has only 1. If you are planning to use multiple monitors, the Fujitsu Esprimo D7010 8 is the better choice.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 3 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.

If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Fujitsu Esprimo D7010 8. Sadly, the HP ProDesk 490 G3 Microtower has no such slot, and you will be forced to use the SATA interface instead.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Looking at the Power Supply Unit (PSU) of the two models we don't see any differences. For either of them you get a maximum power of 300 Watts. However be careful, many models have more than one power supply option. When buying your computer, it is a good idea to get a version with the most powerful PSU. This will potentially allow you to upgrade to a more powerful GPU for example.

Motherboard

Fujitsu_Esprimo_D7010_8_motherboard.jpg motherboard layoutHP_ProDesk_490_G3_Microtower_motherboard.jpg motherboard layout