Fujitsu Esprimo D538 vs. HP ProDesk 490 G1 Microtower

Comparison and Differences

Fujitsu_Esprimo_D538.jpg case front and back pannelHP_ProDesk_490_G1_Microtower.jpg case front and back pannel
Model
Form factorSmallMini Tower
CPU optionsIntel Gen8&9 i3/i5/i7; Pentium; CeleronIntel Gen4 i3/i5/i7; Celeron; Pentium;
ChipsetH310H81
Dedicated GPU *Radeon RX 6400 Low ProfileGeForce GTX 1660 Super
RAMUDIMM DDR4-2666DIMM DDR3-1600
RAM slots24
RAM speed2666 MT/s1600 MT/s
RAM max32 GB32 GB
USB ports(4x) USB-A 3.0; (4x) USB-A 2.0(4x)USB-A 3.0; (6x)USB-A 2.0;
Video portsDisplayPort 1.2; DVIDVI-D; VGA;
Other portsRJ45; Headphones; Mic; Line in; Line out; PS/2RJ45; Hdph; Mic; Line-Out; Line-In; Serial; (2x) PS2;
Optional portsVGA; eSATASD card reader; DisplayPort 1.2; Serial; Parallel;
SATA ports34
PCI slotsPCIe 3.0 x16; PCIe 2.0 x16 (wired x4)PCIe x16; (3x) PCIe x1;
M.2 slotsM.2 2280/2230 M-key (PCIe 2.0 x2, NVMe)N.A.
Drive bays3.5in; 2.5in; 5.25 inch(3x) 3.5in; (2x) 5.25in
PSU210/280 W300 W
Weight5.00 kg (11.03 lb)7.1 kg (15.7 lb)
Released20182013
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Fujitsu Esprimo D538 and HP ProDesk 490 G1 Microtower

If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo D538 which was released in 2018. The HP ProDesk 490 G1 Microtower is older and entered production in 2013.

If you are looking for the smaller form factor the Fujitsu Esprimo D538 is the right one for you. It is smaller than the HP ProDesk 490 G1 Microtower and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo D538 as it is running a newer generation CPU. This is not to say that HP ProDesk 490 G1 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

The HP ProDesk 490 G1 Microtower has 4 RAM slots while the Fujitsu Esprimo D538 has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.

The Fujitsu Esprimo D538 is using the faster 2666 MT/s RAM. The HP ProDesk 490 G1 Microtower is slower by supporting RAM speeds of up to 1600 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 32 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.

Ports

In total the HP ProDesk 490 G1 Microtower has 10 USB ports. The Fujitsu Esprimo D538 is inferior in this regard and packs 8 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.

Unfortunately, only the Fujitsu Esprimo D538 has a DisplayPort. The HP ProDesk 490 G1 Microtower does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 490 G1 Microtower is better equipped as it comes with 4 SATA slot(s), while the Fujitsu Esprimo D538 has 3 slot(s).

If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Fujitsu Esprimo D538. Sadly, the HP ProDesk 490 G1 Microtower has no such slot, and you will be forced to use the SATA interface instead.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Fujitsu Esprimo D538 comes with a decent 280 Watt PSU, but the HP ProDesk 490 G1 Microtower has a more powerful one rated at 300 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.

Motherboard

Fujitsu_Esprimo_D538_motherboard.jpg motherboard layoutHP_ProDesk_490_G1_Microtower_motherboard.jpg motherboard layout