Fujitsu Esprimo D6011 vs. HP ProDesk 400 G2 Microtower

Comparison and Differences

Fujitsu_Esprimo_D6011.jpg case front and back pannelHP_ProDesk_400_G2_Microtower.jpg case front and back pannel
Model
Form factorSmallMini Tower
CPU optionsIntel Gen10&11 i3/i5/i7Intel Gen4 i3/i5/i7; Celeron; Pentium;
ChipsetB560H81
Dedicated GPU *Radeon RX 6400 Low ProfileGeForce GTX 1660 Super
RAMUDIMM DDR4-3200DIMM DDR3-1600
RAM slots42
RAM speed3200 MT/s1600 MT/s
RAM max128 GB16 GB
USB ports(4x) USB-A 3.0; (4x) USB-A 2.0(2x)USB-A 3.0; (4x)USB-A 2.0;
Video ports(2x) DisplayPort 1.2VGA; DVI-D;
Other portsRJ45; Headset, Line in; Line outRJ45; Hdph; Mic; Line-Out; Line-In; Serial; (2x) PS2; SD card reader (USB-? 2.0);
Optional portsN.ASerial; Parallel;
SATA ports33
PCI slotsPCIe 3.0 x16 (wired x4)PCIe x16; (3x) PCIe x1;
M.2 slotsM.2 2280/2230 M-key (PCIe 3.0 x4, NVMe)N.A.
Drive bays(2x) 3.5in; 2.5in; 5.25 inch slim(2x) 3.5in; 5.25in (slim)
PSU280/300 W180/300 W
Weight8.00 kg (17.64 lb)6.5 kg (14.33 lb)
Released20212014
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Fujitsu Esprimo D6011 and HP ProDesk 400 G2 Microtower

If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo D6011 which was released in 2021. The HP ProDesk 400 G2 Microtower is older and entered production in 2014.

If you are looking for the smaller form factor the Fujitsu Esprimo D6011 is the right one for you. It is smaller than the HP ProDesk 400 G2 Microtower and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo D6011 as it is running a newer generation CPU. This is not to say that HP ProDesk 400 G2 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

The Fujitsu Esprimo D6011 has 4 RAM slots while the HP ProDesk 400 G2 Microtower has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.

The Fujitsu Esprimo D6011 is using the faster 3200 MT/s RAM. The HP ProDesk 400 G2 Microtower is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Fujitsu Esprimo D6011 as it has the ability to run 128 GB of RAM. The HP ProDesk 400 G2 Microtower can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.

Ports

In total the Fujitsu Esprimo D6011 has 8 USB ports. The HP ProDesk 400 G2 Microtower is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.

Unfortunately, only the Fujitsu Esprimo D6011 has a DisplayPort. The HP ProDesk 400 G2 Microtower does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 3 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.

If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Fujitsu Esprimo D6011. Sadly, the HP ProDesk 400 G2 Microtower has no such slot, and you will be forced to use the SATA interface instead.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Looking at the Power Supply Unit (PSU) of the two models we don't see any differences. For either of them you get a maximum power of 300 Watts. However be careful, many models have more than one power supply option. When buying your computer, it is a good idea to get a version with the most powerful PSU. This will potentially allow you to upgrade to a more powerful GPU for example.

Motherboard

Fujitsu_Esprimo_D6011_motherboard.jpg motherboard layoutHP_ProDesk_400_G2_Microtower_motherboard.jpg motherboard layout