Fujitsu Esprimo P9010 vs. HP ProDesk 400 G1 Microtower

Comparison and Differences

Fujitsu_Esprimo_P9010.jpg case front and back pannelHP_ProDesk_400_G1_Microtower.jpg case front and back pannel
Model
Form factorMini TowerMini Tower
CPU optionsIntel Gen10 i3/i5/i7/i9Intel Gen4 i3/i5/i7; Celeron; Pentium;
ChipsetQ470H81
Dedicated GPU *GeForce GTX 1650 SuperGeForce GTX 1660 Super
RAMUDIMM DDR4-2933DIMM DDR3-1600
RAM slots42
RAM speed2933 MT/s1600 MT/s
RAM max128 GB16 GB
USB ports(2x) USB-A 3.0; (4x) USB-A 2.0; (4x) USB-A 3.1; USB-C 3.1(2x)USB-A 3.0; (6x)USB-A 2.0;
Video ports(2x) DisplayPort 1.2DVI-D; VGA;
Other portsRJ45; Headset, Line in; Line outRJ45; Hdph; Mic; Line-Out; Line-In; Serial; (2x) PS2;
Optional portsSerial; Parallel; PS/2; VGA; DVI; USB-C 3.1 (DP support 60W/15W)Media card reader (USB 2.0); Serial; Parallel;
SATA ports44
PCI slotsPCIe 3.0 x16; PCIe 3.0 x1; PCIe 3.0 x16 (wired x4)PCIe x16; (3x) PCIe x1;
M.2 slots(2x) M.2 2280/2230 M-key (PCIe 3.0 x4, NVMe); M.2 2230 (WiFi/BT)N.A.
Drive bays(3x) 3.5in; 2.5in; (2x) 5.25 inch(3x) 3.5in; (2x) 5.25in
PSU280/300 W300 W
Weight10.00 kg (24.00 lb)7.1 kg (15.75 lb)
Released20202013
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Fujitsu Esprimo P9010 and HP ProDesk 400 G1 Microtower

If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo P9010 which was released in 2020. The HP ProDesk 400 G1 Microtower is older and entered production in 2013.

Both models have the same form factor, meaning reoughtly they have the same phiysical size and form.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo P9010 as it is running a newer generation CPU. This is not to say that HP ProDesk 400 G1 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

The Fujitsu Esprimo P9010 has 4 RAM slots while the HP ProDesk 400 G1 Microtower has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.

The Fujitsu Esprimo P9010 is using the faster 2933 MT/s RAM. The HP ProDesk 400 G1 Microtower is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Fujitsu Esprimo P9010 as it has the ability to run 128 GB of RAM. The HP ProDesk 400 G1 Microtower can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.

Ports

In total the Fujitsu Esprimo P9010 has 11 USB ports. The HP ProDesk 400 G1 Microtower is inferior in this regard and packs 8 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Fujitsu Esprimo P9010, is that it has 5 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the HP ProDesk 400 G1 Microtower has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.

Unfortunately, only the Fujitsu Esprimo P9010 has a DisplayPort. The HP ProDesk 400 G1 Microtower does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 4 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.

If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Fujitsu Esprimo P9010. Sadly, the HP ProDesk 400 G1 Microtower has no such slot, and you will be forced to use the SATA interface instead.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Looking at the Power Supply Unit (PSU) of the two models we don't see any differences. For either of them you get a maximum power of 300 Watts. However be careful, many models have more than one power supply option. When buying your computer, it is a good idea to get a version with the most powerful PSU. This will potentially allow you to upgrade to a more powerful GPU for example.

Motherboard

Fujitsu_Esprimo_P9010_motherboard.jpg motherboard layoutHP_ProDesk_400_G1_Microtower_motherboard.jpg motherboard layout