Dell OptiPlex 5070M vs. HP ProDesk 600 G2 SFF

Comparison and Differences

Dell_OptiPlex_5070M.jpg case front and back pannelHP_ProDesk_600_G2_SFF.jpg case front and back pannel
Model
Form factorMicroSmall
CPU optionsIntel Gen8&9 i3/i5/i7; Celeron; Pentium;Intel Gen6 i3/i5/i7; Celeron; Pentium;
ChipsetQ370Q150
Dedicated GPU *N.A.GeForce GT 1030 Low Profile
RAMSODIMM DDR4-2400/2666DIMM DDR4-2133
RAM slots24
RAM speed2666 MT/s2133 MT/s
RAM max32 GB64 GB
USB portsUSB 3.1 Type C; (5x) USB-A 3.0;(6x)USB-A 3.0; (4x)USB-A 2.0;
Video ports(2x) Display Port 1.2;(2x) DisplayPort: VGA
Other portsRJ45; Headset; Line-Out; RJ45; Hdph; Mic; Line-Out; Line-In; Serial; (2x) PS2;
Optional portsHDMI2.0b/DP1.2/VGA/USB Type-C (DP Alt Mode); Serial; Serial+PS2; WiFi antenna;Media card reader (USB 2.0); Serial;
SATA ports13
PCI slotsN.A.PCIe 3.0 x16; (3x) PCIe x1;
M.2 slotsM.2 2280/2230 M-key (PCIe 3.0 x4, NVMe); M.2 2230 (WiFi/BT) N.A.
Drive bays2.5in2.5in; (2x) 3.5in; 5.25in (slim)
PSU90 W200 W
Weight1.18 kg (2.60 lb)6.9 kg (16.7 lb)
Released20192015
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Dell OptiPlex 5070M and HP ProDesk 600 G2 SFF

If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 5070M which was released in 2019. The HP ProDesk 600 G2 SFF is older and entered production in 2015.

If you are looking for the smaller form factor the Dell OptiPlex 5070M is the right one for you. It is smaller than the HP ProDesk 600 G2 SFF and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 5070M as it is running a newer generation CPU. This is not to say that HP ProDesk 600 G2 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

The HP ProDesk 600 G2 SFF has 4 RAM slots while the Dell OptiPlex 5070M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.

The Dell OptiPlex 5070M is using the faster 2666 MT/s RAM. The HP ProDesk 600 G2 SFF is slower by supporting RAM speeds of up to 2133 MT/s. Additionally, if you will be needing a lot of RAM, better go for the HP ProDesk 600 G2 SFF as it has the ability to run 64 GB of RAM. The Dell OptiPlex 5070M can do a bit less at max 32 GB. Most of the times, this should be sufficient for the majority of users.

Ports

In total the HP ProDesk 600 G2 SFF has 10 USB ports. The Dell OptiPlex 5070M is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Dell OptiPlex 5070M, is that it has 1 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the HP ProDesk 600 G2 SFF has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.

The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 600 G2 SFF is better equipped as it comes with 3 SATA slot(s), while the Dell OptiPlex 5070M has 1 slot(s).

If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Dell OptiPlex 5070M. Sadly, the HP ProDesk 600 G2 SFF has no such slot, and you will be forced to use the SATA interface instead.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 5070M comes with a decent 90 Watt PSU, but the HP ProDesk 600 G2 SFF has a more powerful one rated at 200 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.

Motherboard

Dell_OptiPlex_5070M_motherboard.jpg motherboard layoutHP_ProDesk_600_G2_SFF_motherboard.jpg motherboard layout