Alienware X51 R3 vs. Dell OptiPlex 9020M

Comparison and Differences

Alienware_X51_R3.jpg case front and back pannelDell_OptiPlex_9020M.jpg case front and back pannel
Model
Form factorSmall GamingMicro
CPU optionsIntel Gen6 i3/i5/i7;Intel Gen4 i3/i5/i7;
ChipsetZ170Q87
Dedicated GPU *GeForce GTX 1650 SuperN.A.
RAMDIMM DDR3-2133SODIMM DDR3-1600
RAM slots22
RAM speed2133 MT/s1600 MT/s
RAM max32 GB16 GB
USB ports(4x) USB 3.0 Type A; (2x) USB-A 2.0; (2x) USB 3.1 Type A(6x) USB-A 3.0
Video portsHDMI 1.4b;DisplayPort 1.2; VGA;
Other portsRJ45; Headset; Line-Out; Line-In; S/PDFI optical/analog;RJ45; Headset; Mic/Hdph;
Optional portsN.A.WiFi antenna; HDMI; DisplayPort; Serial; Serial+PS2;
SATA ports31
PCI slotsPCIe 3.0 x16;N.A.
M.2 slotsN.A.M.2 2230 (WiFi/BT); M.2 2280 B-Key (SATA only);
Drive bays(2x) 2.5in; 3.25in; 5.25in;2.5in
PSU180/240/330 W65 W
Weight5.49 kg (12.10 lbs1.28 kg (2.82 lb)
Released20152013
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Alienware X51 R3 and Dell OptiPlex 9020M

If you are looking for a more modern desktop, then you should go with the Alienware X51 R3 which was released in 2015. The Dell OptiPlex 9020M is older and entered production in 2013.

If you are looking for the smaller form factor the Dell OptiPlex 9020M is the right one for you. It is smaller than the Alienware X51 R3 and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Alienware X51 R3 as it is running a newer generation CPU. This is not to say that Dell OptiPlex 9020M is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.

The Alienware X51 R3 is using the faster 2133 MT/s RAM. The Dell OptiPlex 9020M is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Alienware X51 R3 as it has the ability to run 32 GB of RAM. The Dell OptiPlex 9020M can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.

Ports

In total the Alienware X51 R3 has 8 USB ports. The Dell OptiPlex 9020M is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Alienware X51 R3, is that it has 2 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the Dell OptiPlex 9020M has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.

The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Alienware X51 R3 is better equipped as it comes with 3 SATA slot(s), while the Dell OptiPlex 9020M has 1 slot(s).

If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Dell OptiPlex 9020M. Sadly, the Alienware X51 R3 has no such slot, and you will be forced to use the SATA interface instead.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 9020M comes with a decent 65 Watt PSU, but the Alienware X51 R3 has a more powerful one rated at 330 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.

Motherboard

Alienware_X51_R3_motherboard.jpg motherboard layoutDell_OptiPlex_9020M_motherboard.jpg motherboard layout