Alienware Area 51 R2 vs. Dell OptiPlex 7050 SFF
Comparison and Differences
Differences between Alienware Area 51 R2 and Dell OptiPlex 7050 SFF
If you are looking for a more modern desktop, then you should go with the Alienware Area 51 R2 which was released in 2018. The Dell OptiPlex 7050 SFF is older and entered production in 2017.
If you are looking for the smaller form factor the Dell OptiPlex 7050 SFF is the right one for you. It is smaller than the Alienware Area 51 R2 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Alienware Area 51 R2 as it is running a newer generation CPU. This is not to say that Dell OptiPlex 7050 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Alienware Area 51 R2 is using the faster 2667 MT/s RAM. The Dell OptiPlex 7050 SFF is slower by supporting RAM speeds of up to 2400 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
Both models have the same amount of USB ports for total count of 10. If this is not enough, using a USB hub is always a viable option. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
Unfortunately, only the Dell OptiPlex 7050 SFF has a DisplayPort. The Alienware Area 51 R2 does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
The Dell OptiPlex 7050 SFF comes with an HDMI port, while the Alienware Area 51 R2 does not support the interface. Of course missing HDMI port is something that can be easily fixed with a good adapter (e.g. DisplayPort to HDMI).
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Alienware Area 51 R2 is better equipped as it comes with 6 SATA slot(s), while the Dell OptiPlex 7050 SFF has 3 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Dell OptiPlex 7050 SFF. Sadly, the Alienware Area 51 R2 has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 7050 SFF comes with a decent 180 Watt PSU, but the Alienware Area 51 R2 has a more powerful one rated at 1500 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
